This assignment is based on IT Networking Principles. Please ensure you have read the instructions and are well proficient on what is being asked before submitting your bid.
Please see the attachment for the instructions and what is being asked of this assignment.
Objective
The
overall objective of this laboratory exercise is to gain experience with basic
Cisco switch configuration commands and gain an introductory understanding of
the following:
1. Operating
in the Cisco’s Privileged mode
2. Configuring
the switch ports
3. Configuring
the computers network interface
4. Troubleshooting
the switch Interface
Topology
Figure 1
The Network Topology for This Lab.
Key Concepts
The
following concepts, terms, commands, and steps should have been mastered in
this exercise.
1. Steps to
enter the switch’s privileged EXEC mode (switch#)
2. Use of
the following commands to verify their operation in Cisco IOS.
?, show flash, show version [sh ver], show history [sh hist], show interfaces [sh int], configure
terminal [conf t], interface FastEthernet [interface number], [int fa 0/0],
interface GigabitEthernet
[interface number], [int gi 0/1], interface [vlan number],
int vlan 1]
3. What
happens when you press the up arrow key on your keyboard?
4. How to change
the hostname of the switch
5. How to
configure the switch’s enable secret
6. How to
set the vty password
7. The steps
for configuring the IP address for FastEthernet interface 0/0 [Fa0/0] on your
switch.
8. The use
of the no shut command to enable the
VLAN interface.
9. The use
the sh
vlan brief command to verify that the interfaces have been
configured.
10. Use the
ping command to verify network connectivity
11. Use the ipconfig
/all
12. The steps
for verifying the entries into the switch’s mac address table
13. The steps
for configuring the switch port settings
14. The steps
for configuring the default-gateway for the switch
Reference
Tables
For convenience Table 1 provides the IP
addresses and masks of all necessary interfaces used in the network topology
for this lab.
Table
1 Computer IP Addresses,
subnet masks and gateway address for this lab.
Computer
IP
Address
Subnet
Mask
Gateway
Address
PC1
192.168.21.8
255.255.255.240
192.168.21.1
PC2
192.168.21.6
255.255.255.240
192.168.21.1
S1
192.168.21.5
255.255.255.240
192.168.21.1
SwitchA
192.168.21.10
255.255.255.240
192.168.21.1
R1-Fa0/0
192.168.21.1
255.255.255.240
——————
Detailed
Lab steps
Task
#1
1.
List command sequence to configure (assign)
the IP address settings for the router (R1),
and the computers,PC1, PC2, and S1 for the network provided in Figure 1. Use
the IP addresses provided in Table 1.
2.
List command sequence to configure switch 1 (SW1) to operate in the network using the IP address,
subnet mask, and gateway address specified in Table 1.
3.
What command is used to
enter the switch’s Privileged mode? List
the prompt and the command
4.
Use the following commands
to verify their operation in Cisco IOS.
(a)
What happens when you enter a ? at the switch# prompt?
(b)
What information is
displayed when you enter show flash
at the switch# prompt?
(c)
What command can you use to
view the switch’s uptime?
(d)
How long has the switch
been up?
(e)
What version of the Cisco
IOS software is running on this simulator?
(f)
What command can you use to
view the past entries on this switch?
(g)
What happens when you press
the up/down keys on your keyboard?
(h)
What is the command for
listing the switch’s current configuration?
5.
List the command sequence
required to enter the privileged mode and change the hostname of the switch to SwitchA.
6.
List the command sequence
required to configure the enable secret on the switch to be ciscopress.
7.
List the command sequence
required to set the console password on the switch to ciscopress and enable login.
8.
List the command sequence
required to set the vty password on
the switch to ciscopress and enable
login.
9.
List the command sequence required to enter
port configuration mode for interface FastEthernet 0/1. In this mode, what
tasks are performed by running speed 100 and duplex full commands?
10.
List the command sequence
required to shut down the
FastEthernet 0/5 interface on SwitchA.
11.
List the proper command to
display the status of the FastEthernet
0/5 interface.
12.
List the proper command to view
the switch’s MAC address table.
13.
What commands can be used
to view the static or dynamic mac addresses?
14.
What command can be used to
verify that the interfaces on the switch have been properly configured?
Task #2 Configuration List
The following is a partial list of the items displayed
when you issue the command show
running-configuration [sh run] on a switch.
Your task is to define each item and its purpose. You may need to go to the Cisco website (www.cisco.com) and look up what each of these
commands mean.
1. no
service pad
2. service
timestamps debug uptime
3. service
timestamps log uptime
4. no
service password-encryption
5. system
mtu routing 1500
6. ip
subnet-zero
7. no
file verify auto
8. spanning-tree mode pvst
9.
spanning-tree
extend system-id
10.
Vlan internal allocation policy ascending
Last Completed Projects
| topic title | academic level | Writer | delivered |
|---|